The weather began to cool. The first thing we felt was our hands, because it was clear that the tap water was much cooler than before. When it comes to tap water, we had to discuss the faucets and sinks in the house. What do you need to pay attention to when installing a faucet sink?
Molin sink Moen faucet
Hot and cold mixing faucet installation Note:
1. General mixing faucets are shipped with the installation dimension drawing and instruction manual.
2, before the installation and use should open the goods packaging inspection certificate so as to avoid the use of three products. If imported goods should be more careful.
In addition, should check the hardware accessories are complete, the general hardware accessories should be equipped with: sets of fixed bolts and fixed copper pieces and gaskets; a full set of basins to pull the water heater; two water inlet pipe. To remove the tap, pull the handles up and down, and feel the lightness of the opening and closing and a gentle and even block is appropriate. The next step is to check the plated surface with light, no bubbles, and scratches.
3. If the faucet is used in a new house, there will be sand and other impurities in the water in the newly paved water network. Before installation, water should be drained for a long time until the water quality becomes clear. Install one end of two inlet pipes on the faucet, and the other end connects two hot and cold angle valves or connect two hot and cold joints.
4, the basin to the water installation, connected to the pelvic floor to pull the water, the end connected to the "S" or "P"-shaped elbow. Do not use too much force to cause man-made damage when you turn on the device. After use, the faucet surface should be wiped clean. After a period of time, cut off the flow of hot and cold water. Use a spanner to carefully unscrew the water spout strainer to clean the impurities and install it carefully.
5, many faucet production companies have a certain quality assurance commitment to the product, the general leading manufacturers to implement three-year quality assurance to users, commitment to product quality problems within three years of free repair, can enjoy lifelong service after three years.
Sink installation process
1. Preparation
The position of the sink is different for each family. Therefore, the position of the sink should be consistent with the volume of the sink. When ordering the table, the approximate size of the sink of the counter supplier should be informed so that the sink will not be reworked. The problem.
2, faucet installation
Before installing the sink, both the faucet and the inlet pipe should be installed. When installing a faucet, it requires not only a firm installation, but also no water seepage at the joint.
3, place the sink
After installing some functional parts of the water tank, you can place the water tank in the corresponding position in the table, ready to start the next installation procedure.
4, start the installation
Install the faucet inlet pipe. Connect one end of the inlet pipe that was previously installed on the faucet to the water inlet switch. When installing, pay attention to the firmness of the joint, and pay attention to a detail that is the location of the hot and cold water pipes. Do not mistake the right or left.
5, install the overflow hole of the water pipe
The overflow hole is a protection hole for avoiding water overflow from the water tank. Therefore, when installing the water pipe under the overflow hole, pay attention to the sealing of the water pipe to the joint of the tank body, and ensure that the water pipe of the overflow hole does not leak water.
6, install the filter basket of the water pipe
Under the filter basket under the installation of the water pipe, the main attention to the connection between the water pipe and the tank body, not only to be strong, but also to seal.
7, install the whole drainage pipe
Usually people will buy two sinks with filter baskets, but the distance between the two downcomers is far and far. When the workers are installing, they will cut the supporting drainage pipes according to the actual situation. At this time, pay attention to each interface. Between the seals.
8, install the hanging piece reinforced tank
After the sink is placed on the countertop, it is necessary to install a matching hanging piece between the tank body and the countertop to install the sink securely so as to prevent the tank body from shaking around with small gaps.
9, installation and finishing
Drainage test was conducted. After the basic installation was completed, the filter basket was also installed and the next experiment was started. When doing the drainage test, it is necessary to fill the water tank with water, and test the drainage of the water under the two filter baskets and overflow holes. When draining water, if any water seepage is found, it should be reworked immediately to ensure that it will not be used in the future.
Seal the edge of the tank, and after finishing the drainage test, make sure that the tank is sealed without problems. When sealing with silicone, it is necessary to ensure that the gap between the sink and the table is even and there must be no seepage.
10, complete the installation of the sink
After the edge sealing is completed, the installation of the sink is successfully completed. Although the sink is small, but because of its daily use more frequently, the connection and installation of each water is more critical.
Sink Hardware Faucet Switch House
A Fertilizer or fertiliser is any material of natural or synthetic origin (other than liming materials) that is applied to soils or to plant tissues (usually leaves) to supply one or more plant nutrients essential to the growth of plants.
Fertilizers enhance the growth of plants. This goal is met in two ways, the traditional one being additives that provide nutrients. The second mode by which some fertilizers act is to enhance the effectiveness of the soil by modifying its water retention and aeration. This article, like many on fertilizers, emphasises the nutritional aspect. Fertilizers typically provide, in varying proportions.
Fertilizers are classified in several ways. They are classified according to whether they provide a single nutrient (e.g., K, P, or N), in which case they are classified as "straight fertilizers." "Multinutrient fertilizers" (or "complex fertilizers") provide two or more nutrients, for example N and P. Fertilizers are also sometimes classified as inorganic (the topic of most of this article) versus organic. Inorganic fertilizers exclude carbon-containing materials except ureas. Organic fertilizers are usually (recycled) plant- or animal-derived matter. Inorganic are sometimes called synthetic fertilizers since various chemical treatments are required for their manufacture.
We mainly supply Phosphate fertilizer, such as: MAP, MKP and Silicate fertilizer, like: Potassium Silicate
Fertilizer
Fertilizer,Monopotassium Phosphate MKP,Dipotassium Phosphate
SJZ Chenghui chemical co ltd , http://www.chenghuichemicals.com