The serious harm caused by thunder and lightning to modern life has aroused great concern from all walks of life for the work of mine prevention. The relevant state departments have actively increased their policy support for the lightning protection industry, and more and more enterprises and large-scale social organizations continue to increase their protection against lightning. The capital investment has prompted the market demand for lightning protection industry is also growing. In the future, lightning protection products will be widely used. The installation methods and precautions for lightning protection products must be understood.
Lightning protection product installation method 1) The lightning protection product shall be as close as possible to the equipment to be protected, especially the distance between the signal lightning protection device and the equipment shall not be more than 1 meter.
2) Power supply lightning protection products are basically connected in parallel to ground.
3) Signal lightning protection products are basically connected in series.
4) The installation of lightning protection products must pay attention to the direction, especially signal lightning protection devices, and the OUT terminals of all signal lightning protection devices are connected to the protected devices.
5) When the lightning arrester with a ground wire is installed, the ground wire on the lightning arrester must be welded to the ground wire and wrapped with insulating tape.
6) The grounding lead of the signal lightning protector is usually made of multiple insulated copper wires. The cross-sectional area should not be less than 1.5 square meters, and the combined rack-type lightning protector should not be less than 6 square meters.
Lightning protection product installation precautions
1) Before installation, confirm that the selected model is correct and cannot be mixed.
2) All lightning protection devices must be grounded and meet national standards.
3) The connection line of the lightning arrester should ensure good contact and must not be loosened. There must be no overlapping between the line wires.
4) When the terminal-type signal surge protector is connected, it is necessary to pay attention to the serial number of the surge protector, so that one-to-one correspondence can be made.
5) The connection line between the arrester and the protected equipment should be as short as possible and should not exceed 0.5 meters.
6) In order to ensure the lightning protection effect, the corresponding network surge protectors shall be installed on solid core lines such as power lines and network lines, and equipotential bonding, wiring, and grounding shall be performed in accordance with standards.
Lightning protection product installation method 1) The lightning protection product shall be as close as possible to the equipment to be protected, especially the distance between the signal lightning protection device and the equipment shall not be more than 1 meter.
2) Power supply lightning protection products are basically connected in parallel to ground.
3) Signal lightning protection products are basically connected in series.
4) The installation of lightning protection products must pay attention to the direction, especially signal lightning protection devices, and the OUT terminals of all signal lightning protection devices are connected to the protected devices.
5) When the lightning arrester with a ground wire is installed, the ground wire on the lightning arrester must be welded to the ground wire and wrapped with insulating tape.
6) The grounding lead of the signal lightning protector is usually made of multiple insulated copper wires. The cross-sectional area should not be less than 1.5 square meters, and the combined rack-type lightning protector should not be less than 6 square meters.
Lightning protection product installation precautions
1) Before installation, confirm that the selected model is correct and cannot be mixed.
2) All lightning protection devices must be grounded and meet national standards.
3) The connection line of the lightning arrester should ensure good contact and must not be loosened. There must be no overlapping between the line wires.
4) When the terminal-type signal surge protector is connected, it is necessary to pay attention to the serial number of the surge protector, so that one-to-one correspondence can be made.
5) The connection line between the arrester and the protected equipment should be as short as possible and should not exceed 0.5 meters.
6) In order to ensure the lightning protection effect, the corresponding network surge protectors shall be installed on solid core lines such as power lines and network lines, and equipotential bonding, wiring, and grounding shall be performed in accordance with standards.
Roll Up Door Servo Motor,Automatic Roller Shutter Door Opener,Roller Shutter Door Servo System,Glass Sliding Door Motor
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hongfadoor.com