Snap-style solid wood flooring is suitable
If it is geothermal heating, can it be solid wood flooring? Most consumers may think that they cannot shop because solid wood flooring is too easy to crack. Is there any way to overcome this shortcoming?
At present, there is a pure solid wood buckle geothermal heating floor on the market. This type of floor overcomes the disadvantages of easy arching, tile changing, cracking, and detachment from the solid wood floor, and solves the quality problems caused by the wet shrinkage of the solid wood floor. It uses the buckle double spring tension and contraction, and set aside a certain amount of expansion joints in the installation to adjust the solid wood floor wet up dry shrinkage, to solve the problem of easy arching and easy to leave the joints of solid wood flooring. The principle is the use of air heat conduction, effectively solve the solid wood flooring poor thermal conductivity, slow speed, heat loss and other characteristics. The joints between the floor and the floor do not use male and female wedges, and a good number of passages can be formed between the board and the board, between the buckles and the buckles.
When this kind of snap-in floor is installed, there is a gap of 0.2-0.4mm between the board and the board, which not only solves the noise generated during the installation and use of the solid wood floor, but also more importantly changes the conduction of the traditional wood-conductor conductor. The heat transfer and dehumidification methods are air convection heat transfer and dehumidification methods, which help to save energy and reduce floor deformation. This kind of snap-in floor is nail-free, glue-free, and free from keel during the installation process, which reduces the noise pollution during installation and is very simple. It takes only a few minutes to complete the floor replacement that would have taken a few days.
Laminate flooring should use small size
The more geothermal floors currently used on the market are laminate flooring and engineered wood flooring. The thickness of composite flooring is mostly 7 to 8 mm. It is easy to transfer the heat generated by the geothermal system to the surface, and its surface is resistant to metal oxides. In the grinding layer, heat spreads very quickly and evenly over the surface. Imported flooring quality meets the European Enpr13329 standard, and domestic flooring quality meets the national GB/T1802-2000 standard. Both can meet the technical requirements for geothermal heating floor installation. At present, some qualified brands in the market have reached this standard. The effect of the lock-type floor is better, because there is a small gap between the hook floor, so it is not easy to go out after expansion.
In order to increase the amount of heat conduction, the thickness of the cushion material and the floor should not be too thick. The standard thickness of the geothermal floor is 6.5-8.5mm, the reinforced laminate floor should be 6-8mm, and the three-layer parquet is 8-9mm. Consumers are advised to use a small size, preferably a square or herringbone shape of 200×40×10, to make it uniform in thermal deformation. If you choose to strengthen the laminate flooring, you can use special geothermal flooring of famous brands such as Shengxiang, Ruijia, Hongnai, Oudian, and Baili. These manufacturers have strict requirements on the density of the substrate, the same thickness and strength, breathability, heat dissipation and good heat resistance through special treatment. If you choose solid wood flooring can choose Weilun, Fumandi, time and other famous brands of special floor heating.
Installation secret ground floor should strictly abide by the temperature program
1. Gradually warm up after installing for 24 hours. Be sure to keep the floor clean and dry before warming to prevent cracking and distortion of the floor due to excessive heating.
2. When using geothermal heating for the first time or when it has not been turned on for a long time, it should be set to the minimum temperature first, and then slowly increase the temperature. It is advisable to raise the temperature by about 1°C per hour, so that the wooden floor gradually adapts to the temperature rise. If the heating is too fast, it may cause the wooden floor to be heated too fast, resulting in unstable twisting and cracking changes, affecting the service life of the wooden floor.
3. As far as possible in the geothermal heating of the wooden floor as a fixed decoration or furniture without legs, to prevent local heat is not smooth, heat boring in the wood floor, easy to produce uneven deformation of the floor due to heat.
Nature Flooring Del Floor Space Decoration Furniture
Scotias,PVC Flooring Accessories T-moulding,Floor WPC End Cap,Wpc Stair Nose For Stair
JIANGSU PERFECT NEW MATERIAL TECHNOLOGY CO., LTD. , https://www.bffloor.com