In the home improvement, the ceiling is an essential environment. Soft film ceiling has become an increasingly popular ceiling material, we know that in many places, the design is very critical, soft film ceilings just meet this feature, so a variety of high-end products have emerged, soft film ceiling construction process What is it like? What should you pay attention to when constructing a soft film ceiling ? Following Xiaobian look at it.
Soft film ceiling construction technology
1. When installing undulations, each wavy bottom frame with the keel installed is consistent, so that after the flexible membrane is installed, the wavy shape is neatly coordinated.
2, and the soft membrane contact with the edge of the chassis must be smooth, after the installation of soft film ceiling film ceiling Lapeng ceiling ceiling flexible film ceiling molding ceiling small ceiling shower will not be uneven.
3. If there is a gap between the soft film and the soft film, the suspender and the main keel should be as thin as possible when lifting the underframe. Do covertly and neatly. Looking from the bottom up, you can't see the fixed base boom.
4, install soft film ceiling film Lapeng ceiling smallpox flexible ceiling light film shape ceiling art ceiling shower bath to fully heated, especially in cold places, before opening the crystal wool to be heated to prevent the cold to make the soft film change Brittle, damaged soft film
5, install a circular soft film ceiling film pull ceiling smallpox flexible ceiling light film shape ceiling smallpox art ceiling bath when the ceiling, the flat code to use a bending machine to bend. The arc is smooth and there is no cutting seam.
6, if you use the cutting method to bend, must be cut once every three centimeters, to be uniform, and can not cut more than half the thickness of the keel, otherwise it will appear prismatic.
7. When the time permits, install the keel first, measure the size, and then place the order, which can reduce many quality problems caused by improper modification or size.
Soft film ceiling construction precautions
1, before installation should first look at the site to see if there are no conditions to install the keel, mainly reflected in the wall is completed, whether the carpentry qualified, whether the plastering place is completed, some of the carpentry size must be required to do.
2, before the soft film ceiling installation, we must first check whether the keel joints are firm and smooth, to be sealed at the same place to do a good job, in the sprinkler with a sticky tape. When installing a soft film ceiling, first fix it from both sides of the middle, and pay attention to the installation size. The welding seam should be straight and the corners should be well controlled. After finishing the last four weeks, trim out the extra ceiling and look beautiful.
3, open hole lamp: Make a mark in the lamp hole, pvc ring accurate paste in the bottom of the soft film. Firmly remove excess lace.
4, in the construction site conditions permitting, according to the requirements of the design drawings of woodworking to do some fixed pvc special keel, angular position must be flat and smooth.
5. Air outlet and light pipe tray: Find the location of the air outlet of the air outlet. As with the surrounding area, install the soft film on the special keel for PVC. Note that the corner should be flat. After doing a good job, you can remove more of the smallpox.
6. Finally, clean the soft film ceiling surface with a clean towel.
7. Observe that the lighthouse, tuyere, and light pipe plate must be level with the surrounding keel, and they must be stable and stable without swinging.
8. Smoke, ceiling lamp, first position and then do a wooden chassis, the bottom of the wooden chassis to be polished smooth, and pay attention to the level, too low it is easy to highlight the traces of the chassis.
Editor's summary: The above is related to the introduction of soft film ceilings . Since everyone needs are different, the choice is different. The above information is for your reference. Hope to help friends who have this need!
Construction acceptance decoration construction knowledge construction
Aluminum Threaded Flange is a kind of flange which uses thread to connect with pipeline. When designing, Aluminum Forged Threaded Flange can be treated as loose flange. The advantage of Aluminum 1060 Threaded Flange is that there is no need for welding, and the additional moment produced by flange deformation on cylinder or pipeline is very small. So it's a good choice to choose Aluminum 5083 Threaded Flange.
|
Material |
Aluminium ASTM B241 3003/6061/6063/5083/5086/5052 etc 6061-T6 and 6063-T6 |
|
Standard |
ASME/ANSI B16.5: WELDING NECK FLANGE, SLIP-ON FLANGE, Blind Flange , HIGH HUB BLIND FLANGE, |
|
Size |
1/2" - 20 " (DN15-DN3000) |
|
Pressure |
Class150-Class2500 |
|
Packing |
Pallet/Wooden case(Fumigation free) |
|
Certificate |
ISO9001,EN10204 3.1 MTC |
|
Quality control |
In house and third party |
Aluminum Threaded Flange
Aluminum Forged Threaded Flange, Aluminum 1060 Threaded Flange, Aluminum 5083 Threaded Flange, Aluminum 6061 Threaded Flange, Aluminum 6061T6 Threaded Flange
HEBEI HANMAC MACHINE CO., LTD. , https://www.chinahanmac.com